Juniper Junos devices
Install Junos device
This is the request to install Junos device:
curl -X PUT \
http://localhost:8181/rests/data/network-topology:network-topology/topology=topology-netconf/node=junos \
-d '{
"node": [
{
"node-id": "junos",
"netconf-node-topology:host": "10.10.199.47",
"netconf-node-topology:port": 830,
"netconf-node-topology:tcp-only": false,
"netconf-node-topology:username": "USERNAME",
"netconf-node-topology:password": "PASSWORD",
"netconf-node-topology:session-timers" : {
"netconf-node-topology:keepalive-delay": 50000
},
"uniconfig-config:uniconfig-native-enabled": true,
"uniconfig-config:install-uniconfig-node-enabled": true,
"uniconfig-config:blacklist": {
"uniconfig-config:path": []
}
}
]
}'
Where:
- junos: is the name of the device
- 10.10.199.47: is the ip address of the device
- 830: is the port number of the device
- USERNAME: is the username to access the device
- PASSWORD: is the respective password
- "uniconfig-config:uniconfig-native-enabled": allows to enable installing through UniConfig Native
- "uniconfig-config:install-uniconfig-node-enabled": allows to disable installing to uniconfig and unified layers
- "uniconfig-config:path": allows to specify a list of root elements from models present on device to be ignored by UniConfig Native
Show configuration
To show all the configurations loaded in config datastore, run:
curl -X GET \
http://localhost:8181/rests/data/network-topology:network-topology/topology=uniconfig/node=junos?content=config
In case of success it will respond something similar to:
{
"node": [
{
"node-id": "junos",
"frinx-uniconfig-topology:configuration": {
"configuration:configuration": {
"interfaces": {
"interface": [
{
"name": "fxp0",
"unit": [
{
"name": "0",
"family": {
"inet": {
"dhcp": {
"vendor-id": "Juniper-vmx"
}
}
}
}
]
},
{
"name": "ge-0/0/2",
"disable": [
null
]
},
{
"name": "ge-0/0/3",
"disable": [
null
]
},
{
"name": "ge-0/0/0",
"disable": [
null
]
},
{
"name": "ge-0/0/1",
"disable": [
null
]
}
]
},
...
Show interface configuration
To show the configuration related to a specific interface, in this case “ge-0/0/2”, run:
curl -X GET \
http://localhost:8181/rests/data/network-topology:network-topology/topology=uniconfig/node=junos/frinx-uniconfig-topology:configuration/configuration:configuration/interfaces/interface=%22ge-0/0/2%22?content=config
The response will show the status of the interface:
{
"interface": [
{
"name": "ge-0/0/2",
"disable": [
null
]
}
]
Enable interface in configuration
To enable the interface “ge-0/0/2” in config datastore, run:
curl -X PUT \
http://localhost:8181/rests/data/network-topology:network-topology/topology=uniconfig/node=junos/frinx-uniconfig-topology:configuration/configuration:configuration/interfaces/interface=%22ge-0/0/2%22 \
-d '{
"interface": [
{
"name": "ge-0/0/2"
}
]
}'
Disable interface in configuration
To disable the interface “ge-0/0/2” in config datastore, run:
curl -X PUT \
http://localhost:8181/rests/data/network-topology:network-topology/topology=uniconfig/node=junos/frinx-uniconfig-topology:configuration/configuration:configuration/interfaces/interface=%22ge-0/0/2%22 \
-d '{
"interface": [
{
"name": "ge-0/0/2",
"disable": [
null
]
}
]
}'
After the configuration changes have been done on the config datastore, it is possible to send to the Junos device with the commit request.
